Upgrade Your Kitchen & Bath in the Rio Grande Valley
Plumbing Fixture Installation & Replacement
From sleek kitchen faucets and disposals to shower valves, tub/shower trim, sinks, hose bibs, laundry connections, and fridge water lines, Treviño Repairs installs fixtures cleanly and to code. We verify rough-ins and clearances, check shutoffs and supply/drain condition, and replace angle stops and braided lines when needed. Then we set, level, and seal the fixture, align the trap, connect, and thoroughly test for leaks and proper operation. Finally, we silicone neatly, haul away the old fixture, and leave a polished finish for your home or business.
Services for Plumbing Fixture Installation & Replacement
Treviño Repairs installs and replaces fixtures cleanly and to code. We verify rough-ins and clearances, check shutoffs and supply/drain condition, and complete neat, leak-free connections with a polished finish.
We install & replace — Kitchen:
- Faucets (single-hole, widespread, wall-mount; pull-down & touchless)
- Sinks (drop-in, undermount, farmhouse) with basket strainers
- Garbage disposals (½–1 HP) and air-switches
- Dishwasher hookups and air-gap (where required)
- Fridge/ice-maker water lines and shutoffs
- Pot fillers and under-sink filtration/RO faucetsx
- Post-repair testing (flow/pressure verification)
Bath:
- Lavatory faucets, drains, and pop-up assemblies
- Sinks (pedestal, vessel, undermount/vanity)
- Shower/tub valves (pressure-balance/thermostatic), trim, diverters
- Showerheads, hand showers, slide bars, tub fillers
- Bidet seats/smart bidets (electrical add-on available)
- Pot fillers and under-sink filtration/RO faucetsx
- Post-repair testing (flow/pressure verification)
Laundry/Utility & Outdoor:
- Laundry boxes/valves and washer hose upgrades (braided)
- Utility sinks and faucets
- Hose bibbs/anti-siphon, frost-free spigots, yard hydrants
- Outdoor kitchen sinks/faucets
Code items & setup (as applicable):
- Angle stops and braided supply lines when needed
- Proper P-trap/tailpiece alignment and secure supports/escutcheons
- Air gaps, vacuum breakers/anti-siphon devices where required
- Clean silicone/caulk seals and ADA heights when specified
Upgrades & options:
- Touch/touchless faucets, hot-water dispensers, soap dispensers
- Leak sensors and auto-shutoff valves
- Water-hammer arrestors and pressure checks
- Under-sink filtration and RO systems with dedicated faucets
What Actually Matters in a Quality Fixture
Not all faucets, valves, and trim are built the same. Look for ceramic-disc cartridges (not rubber washers), solid brass or stainless bodies, and PVD or baked finishes that resist corrosion and tarnish. Confirm the basics before you buy: rough-in compatibility, mounting type (single-hole, widespread, wall-mount), flow rates (kitchen/bath, shower), and any code items like air gaps or vacuum breakers where required.
During installation, long-term reliability comes from the details—quarter-turn angle stops, braided stainless supply lines, correct trap/tailpiece alignment, proper sealant/caulk usage, and secure supports so nothing loosens over time. Treviño Repairs verifies specs, installs to code, tests for leaks and smooth operation, and leaves a clean finish for your Rio Grande Valley home or business.
When to Replace or Upgrade Plumbing Fixtures
Persistent drips, stiff or wobbly handles, low or uneven flow after cartridge changes, leaks under sinks or vanities, corroded or hard-to-turn shutoffs, cracked or stained porcelain, and rough-in mismatches during a remodel are all signs it’s time to upgrade. Treviño Repairs evaluates rough-ins, water pressure, and supply/drain condition, replaces angle stops and braided lines when needed, then sets, levels, seals, and tests the new fixture so you get a clean, code-compliant finish for your RGV home or business.
What to Expect with Treviño Repairs
Our Plumbing Fixture Installation Process
We keep it code-compliant, clean, and efficient so your lines protect your home or business.
Assess & Measure. Confirm fixture type and scope, check rough-ins/holes and clearances, verify water pressure, and note any code items (air gap, vacuum breaker, ADA heights).
Protect & Prep. Shoe covers, drop cloths, safe shutoffs, drain-down, and staging of parts/hardware so the workspace stays clean.
Remove & Inspect. Remove the old fixture, clean the surface, inspect flange/mounts, and replace angle stops and braided supply lines when needed.
Set, Level & Secure. Apply proper sealant, set the fixture or sink, level to spec, and anchor with the correct brackets/fasteners.
Connect & Align. Make neat supply connections, align trap/tailpiece and escutcheons, and add required accessories (air gap, vacuum breaker, supports).
Test & Fine-Tune. Purge air, check for leaks, verify flow and temperature, adjust cartridges/stops, and confirm diverter/spray or disposal/dishwasher/fridge hookups.
Clean Up & Walkthrough. Silicone/caulk touch-ups, surface polish, haul-away of the old fixture, and a quick care/warranty review—leaving a neat, code-compliant finish.
Real Stories. Real Results.
What Our Customers Are Saying
Plumbing Fixture Installation Questions, Answered
Straightforward answers before you book—symptoms, costs, fixes.
Can I provide my own fixtures?
Yes. We’ll verify compatibility (mounting type/holes, rough-in, valve type, supply/drain sizes) and let you know if any adapters or parts are needed. Please have all trim, cartridges, and mounting hardware on site.
Do you replace shutoff valves and supply lines?
When needed, yes. We recommend quarter-turn angle stops and braided stainless supply lines for reliability. If existing valves are corroded or seized, we’ll swap them during the install.
What if my sink/counter holes or rough-ins don’t match the new fixture?
We can often solve with base plates/escutcheons, adapter kits, or minor layout adjustments. For shower valves or significant mismatches, we’ll explain options before work begins.
Do I need an air gap or vacuum breaker?
Sometimes. Dishwashers, outdoor hose bibbs, pot fillers, and certain fixtures require backflow protection. We’ll install the appropriate device to meet local code.
How long does installation take—and do you haul away the old fixture?
Many like-for-like swaps are completed the same day. Layout changes, valve moves, or countertop work can add time. Old fixture haul-away and a clean finish are included.
